Accessories


CONTROL, SHUT-OFF AND SOLENOID VALVES

  • KR 2-E DN 20

    MODEL KR 2-E DN 20 THERMOSTATIC CONTROL VALVE, BUILT-IN

    KR-2 thermostatic control valve (through valve) with thermostatic head to regulate a constant air discharge temperature, completely installed. Special valve to control very high volumes of water. kvs value 7.0. Length of capillary tube probe 2m, connection DN 20
  • KR 2-L DN 20

    MODEL KR 2-L DN 20 THERMOSTATIC CONTROL VALVE

    KR-2 thermostatic control valve (through valve) with thermostatic head to regulate a constant air discharge temperature, loose in accessory pack. Special valve to control very high volumes of water. kvs value 5.0. Length of capillary tube probe 2m, connection, connection DN 20.
  • KR 3-L DN 20/25/32

    MODEL KR 3-L DN 20/25/32 THERMOSTATIC CONTROL VALVE

    KR-3-L thermostatic control valve (3-way valve) with thermostatic head to regulate a constant air discharge temperature, loose in accessory pack. Special valve to control very high volumes of water. Length of capillary tube probe 2 m, DN 20 kvs 4.5, DN 25 kvs 6.5, DN 32 kvs 9.5
  • TAV

    MODEL TAV 230 V THERMOELECTRIC SHUT-OFF VALVE

    Normally closed, loose in accessory pack, for shutting off water via summer / winter switch or to regulate water flow rate volumes with customer actuator. Special valve to control very high volumes of water. kvs value 5.0. Connection DN 20
  • MV

    MV 230 V SOLENOID VALVE

    Normally closed, gently closing, for shutting off water
    via summer / winter switch, loose in accessory pack.
    DN 20 kvs 11, DN 25 kvs 13; DN 32 kvs 30.
  • MR 2-E DN 20

    MODEL MR 2-E DN 20 CONTROL VALVE

    MR-2 control valve (through valve)) with electrical actuator to set a constant air discharge temperature. Includes an air discharge temperature sensor, completely installed and wired. The MR 2 control valves are special valves to control very high volumes of water. kvs value 7.5.

DOOR CONTACTS

  • TK

    MODEL TK DOOR CONTACT

    Protection class IP 65, jump feed with H-jumpers, and full contact up to the switchover point, insulated connecting terminals in acc. with VDE 0106 Part 100 (VGB 4), cable entry 2 x PG 13.5, below and at the side, switching voltage 230 V AC, 24 V DC, switching current 6 A AC, 4 A DC.
  • TKB

    MODEL TKB DOOR CONTACT

    Contactless door contact in protection class IP 00, consisting of a dry reed contact and permanent magnet
    for open circuits (contact open when magnet is applied), switching voltage 100 V DC, switching current 250 mA DC.

REPAIR SWITCHES

  • REP-S

    REP-S REPAIR SWITCH

    For switching off the system via the software. Only in conjunction with control systems TLC700, TMC500 and
    TMC300. Switches installed in the device behind the inspection cover.
  • REP-L

    REP-L REPAIR SWITCH

    3-pole repair switch in surface-mounted housing, as loose accessory kit, for customer installation in the device lead.

BRACKETS

  • DH

    DH CEILING BRACKET

    Mounting bracket, vibration damper, 1 m threaded rods, securing and counter nut, anchor bolt, minimum space required 0.1 m, suspension length 1 m (quantity depending on device length and version).
  • DHD

    DHD USER-FRIENDLY CEILING BRACKET

    Mounting bracket, vibration damper 17 dB, turnbuckle, right/left threaded pin, 1 m threaded rods, securing and counter nut, dowel, minimum space required 0.2 m, suspension length 1.1 m (quantity depending on device length and version).

THERMOSTATS

  • FTE

    FTE FROST PROTECTION THERMOSTAT

    To protect hot water heater batteries, with capillary tube probe, capillary tube length 3 m, intrinsically safe, as one-pole potential-free toggle, protection class IP 30,
    ready installed in the device.
  • FTM

    FTM ELECTRONIC FROST PROTECTION THERMOSTAT

    Only in conjunction with controllers TLC700, TMC500 and TMC300. With capillary tube probe, capillary tube length
    0.9 m, protection class IP 30, ready installed in the device, only suitable for low voltage (NO contacts).
  • ERT

    ERT ELECTROMECHANICAL ROOM THERMOSTAT

    5 - 30 °C with bimetal, white (similar to RAL 9010), switching capacity 230 V AC, 50...60 HZ, toggle (changeover) 10
    (4 = inductive load) A, switching differential 0.5 K, protection class IP 30, air humidity 0...95 % non-condensing, operating temperature 0...40 °C, thermal feedback. Dimensions:
    75 x 75 x 25 mm.